Production Capacity Requirements Planning Using The Capacity Method Requirement Planning

Sidik Permana, Meri Andriani, Dewiyana Dewiyana

Abstract


PT. ABC is a company engaged in the manufacture of Dolomite Fertilizer. The number of requests is greater than the amount of production. Due to fluctuations in the number of requests that tend to increase, this occurs due to a lack of capacity at the workstation. Therefore, it is necessary to calculate the capacity requirements planning analysis for each work station to know the company's capacity needs. The research aims to identify the shortage/excess production capacity and provide proposals for the balance of production capacity at PT. A B C. Production capacity research was conducted using the Capacity Requirement Planning (CRP) method. Results and Discussion, comparison of available capacity and required capacity (load) are as follows, work station jaw crusher available capacity 36.74 hours/week while required capacity (load) 36 hours/week, work station bucket elevator available capacity 36, 74 hours/week while the required capacity (load) is 14.4 hours/week, work station ball mill available capacity is 36.74 hours/week while the required capacity (load) is 45.6 hours/week, and work station silo flour the available capacity is 36.74 hours/week while the required capacity (load) is 51.59 hours/week. In conclusion, two stations experience excess capacity, namely the jaw crusher work station with an excess capacity of 0.74 hours/week and the bucket elevator work station with an excess capacity of 22.34 hours/week. The other two work stations experienced a lack of capacity, namely the ball mill work station with a capacity shortage of 22.34 hours/week and the silo flour work station with a capacity shortage of 14.85 hours/week. Efforts to balance capacity by scheduling overtime and adding equipment (machinery) to work centers that lack capacity, so that the company's production targets are achieved.


Keywords


Capacity, Capacity Requirement Planning, Industry, Production, Workstation

References


S. Y. Firiza, “Analisis Perencanaan Pengendalian Produk Hairdryer Carolina 450 Watt Dengan Menggunakan Metode Capacity Requirement Planning ( Crp ) TALENTA Conference Series Analisis Perencanaan Pengendalian Produk Hairdryer Carolina 450 Watt Dengan Menggunakan Metode C,” vol. 3, no. 2, 2020, doi: 10.32734/ee.v3i2.1012.

S. Syafwandi, D. Setyo Sembodo, A. Tua Munthe, and A. Sumarno, “Analysis of The Use of Sawdust Waste As Concrete Mixture Add Material Against Workability and Compressive Strength Concrete With Three Concrete Treatment Methods,” Int. J. Eng. Sci. Inf. Technol., vol. 1, no. 2, 2021, doi: 10.52088/ijesty.v1i2.109.

W. K. Risal, P. Puryani, and E. Nursubiyantoro, “Perencanaan Kebutuhan Kapasitas Produksi Pada Sp Aluminium,” Opsi, vol. 10, no. 1, p. 11, 2017, doi: 10.31315/opsi.v10i1.2105.

V. D. R. Guide and M. S. Spencer, “Rough-cut capacity planning for remanufacturing firms,” Prod. Plan. Control, vol. 8, no. 3, pp. 237–244, 1997, doi: 10.1080/095372897235299.

L. de Sanctis and A. Mandolini, “Bearing Capacity of Piled Rafts on Soft Clay Soils,” J. Geotech. Geoenvironmental Eng., 2006, doi: 10.1061/(asce)1090-0241(2006)132:12(1600).

A. Arsyad, M. Jaksa, W. Kaggwa, and Y. Mitani, “Effect of Radial Distance of a Single Cpt Sounding on the Probability of Over- and Under-Design of Pile Foundation,” in The First Makassar International Conference on Civil Engineering (MICCE2010), 2010.

W. Sukmawati and I. S. Jatmiko, “Rekayasa Kapasitas Produksi Pakaian Hangat (Sweater) Style 120512 Dan Style 193948 Di Pt Aulia Pratama Dengan Metode Capacity Requirement Planning (Crp),” no. 1, pp. 8–17, 2015.

M. F. Firmansyah and H. Z. Maulana, “Empirical Study of E-Learning on Financial Literacy and Lifestyle : A Millenial Urban Generations Cased Study,” Int. J. Eng. Sci. Inf. Technol., vol. 1, no. 3, pp. 75–81, 2021.

A. S. Ahmar et al., “Lecturers’ understanding on indexing databases of SINTA, DOAJ, Google Scholar, SCOPUS, and Web of Science: A study of Indonesians,” in Journal of Physics: Conference Series, 2018, doi: 10.1088/1742-6596/954/1/012026.

M. J. Cassidy, B. W. Byrne, and M. F. Randolph, “A comparison of the combined load behaviour of spudcan and caisson foundations on soft normally consolidated clay,” Geotechnique, 2004, doi: 10.1680/geot.2004.54.2.91.

R. Rahim et al., “Combination Base64 Algorithm and EOF Technique for Steganography,” in Journal of Physics: Conference Series, 2018, vol. 1007, no. 1, doi: 10.1088/1742-6596/1007/1/012003.

S. Sinulingga, “Perencanaan dan Pengendalian Produksi,” Book, 2009.

P. Erlina, “Perencanaan Kapasitas Waktu Produksi Yang Optimal Dengan Menggunakan Metode Capacity Requirement Planning Di Pt. Spi Surabaya,” Tek. Ind. FTI-UPNV Jawa Timur, 2008.

J. C. Pine and S. L. Guillot, “Risk communication,” in Hazards Analysis: Reducing the Impact of Disasters, Second Edition, 2014.

Fatmawati, “Analisis Kapasitas Produksi Dengan metode Capacity Requirement Planning (CRP) Di PT. Hanil Jaya Stell.,” J. Tek. Mesin, vol. 1, no. 2, pp. 351–354, 2013.

S. Wardah and I. Iskandar, “ANALISIS PERAMALAN PENJUALAN PRODUK KERIPIK PISANG KEMASAN BUNGKUS (Studi Kasus : Home Industry Arwana Food Tembilahan),” J@ti Undip J. Tek. Ind., 2017, doi: 10.14710/jati.11.3.135-142.

S. J. Taylor and B. Letham, “Business Time Series Forecasting at Scale,” PeerJ Prepr. 5e3190v2, vol. 35, no. 8, pp. 48–90, 2017.

P. M. Senge, “The fifth discipline, the art and practice of the learning organization,” Perform. + Instr., 1991, doi: 10.1002/pfi.4170300510.

M. Coetzer and L. Tran, “Development of planning rules and an optimised Master Production Schedule for a new water and ice tea bottling plant VOORBLAD VIR INDIVIDUELE WERKOPDRAGTE -2016 FRONT PAGE FOR INDIVIDUAL ASSIGNMENTS -2016 Werkopdrag / Assignment Verklaring / Declaration,” no. October, 2016.

C. Herrera, S. Belmokhtar-Berraf, A. Thomas, and V. Parada, “A reactive decision-making approach to reduce instability in a master production schedule,” Int. J. Prod. Res., vol. 54, no. 8, pp. 2394–2404, 2016, doi: 10.1080/00207543.2015.1078516.

G. Ke, R. S. Chen, Y. C. Chen, S. Wang, and X. Zhang, “Using ant colony optimisation for improving the execution of material requirements planning for smart manufacturing,” Enterp. Inf. Syst., vol. 00, no. 00, pp. 1–23, 2020, doi: 10.1080/17517575.2019.1700552.

GB 50010-2010, Code for design of concrete structures Beijing. 2010.

A. R. Stopczyński, “Estimating the Required Amount of a Bank’s Loss-Absorbing Capacity,” Emerg. Mark. Financ. Trade, vol. 00, no. 00, pp. 1–14, 2020, doi: 10.1080/1540496X.2020.1810012.

M. AB, - Prihandoko, P. E, and W. C, “Analyzing COBIT 5 IT Audit Framework Implementation using AHP Methodology,” JOIV Int. J. Informatics Vis., 2018, doi: 10.30630/joiv.1.2.18.




DOI: https://doi.org/10.52088/ijesty.v1i4.165

Refbacks

  • There are currently no refbacks.


Copyright (c) 2021 Sidik Permana, Meri Andriani, Dewiyana Dewiyana

Creative Commons License
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

International Journal of Engineering, Science and Information Technology (IJESTY) eISSN 2775-2674