Analysis of The Use of Sawdust Waste As Concrete Mixture Add Material Against Workability and Compressive Strength Concrete With Three Concrete Treatment Methods

Syafwandi Syafwandi, Danu Setyo Sembodo, Agyanata Tua Munthe, Agung Sumarno

Abstract


Wood management activities that are often encountered, as in wood cutting activities in the manufacture of wooden handicrafts, basically after this activity can become a problem, namely sawdust waste, where this waste if left for so long will be a big problem and have an impact on the environment. One solution that can be used for the problem of sawdust waste is to mix this sawdust waste into a concrete mixture. This sawdust waste can be used in concrete mixtures because of the cellulose content in sawdust waste which can affect the compressive strength value with different concrete treatment methods (curing) and slump of concrete. In this research included into experimental research with wood used is wood kamper samarinda, from the leftover cutting of wood frames from craftsman wood UD. kembang Arum in Bekasi, West Java.  Using sawdust waste with a size that passes through sieve No.4 (passes through a 4.75 mm) with variaes addition of 0 kg/m3 , 1 kg/m3  dan 1,5 kg/m3, as well as testing with a concrete mixture that has a mix design of 35 MPa f'c which is inserted into the test object in the form of a cylinder with a diameter and height of 15 and 30 cm which is then for the treatment method done by three different methods. The addition of saw dust waste with a varies of 1 kg/m3  dan 1,5 kg/m3   to the concrete mixture makes the slump and workability values decrease, but the slump value obtained is still in accordance with slump value plan. and for compressive strength values with an addition variation of 1 kg / m3 and 1.5 kg / m3 , The compressive strength value changes from the normal compressive strength value of concrete and the effect of the treatment method also affects the compressive strength value obtained.


Keywords


Saw Dust , Workability, Concrete Compressive Strength, Three Method Treatment

Full Text:

PDF

References


A. H. Ujang, A. R. Omar, I. A. Rani, A. Azmi, S. B. M. Kamal, and D. Abdullah, “Factors Influencing Consumer’s Intention to use Self Service Technology in Tourism and Hospitality Industry,” Int. Acad. Res. J. Bus. Technol., 2016.

S. Azhar, W. A. Carlton, D. Olsen, and I. Ahmad, “Building information modeling for sustainable design and LEED ® rating analysis,” Autom. Constr., 2011, doi: 10.1016/j.autcon.2010.09.019.

M. D. Martínez-Aires, M. López-Alonso, and M. Martínez-Rojas, “Building information modeling and safety management: A systematic review,” Safety Science. 2018, doi: 10.1016/j.ssci.2017.08.015.

C. Drive et al., “Experiences from recent European research projects on the interplay between technology and design,” Mater. Des., 2007.

R. Han, Z. Feng, X. Fan, T. Xu, J. Tian, and J. Meng, “A new intelligent VR biological learning system based on natural interaction,” Proc. 2020 IEEE 4th Inf. Technol. Networking, Electron. Autom. Control Conf. ITNEC 2020, no. Itnec, pp. 175–179, 2020, doi: 10.1109/ITNEC48623.2020.9085016.

D. Oktavia, M. M. E. I. Bali, H. Rahman, U. Umar, A. Syakroni, and F. Widat, “Exploration of Fine Motor Skills through the Application of Paint,” in WESTECH, 2019, pp. 1–6, doi: 10.4108/eai.8-12-2018.2284038.

H. Susanto, “”Pengembangan proses pemisahan furfural dari black liquor pemasakan tandan kosong sawit dalam pelarut organik”,” 1998.

P. Barbaro et al., “Safety Data Sheet,” J. Am. Chem. Soc., 2009, doi: 10.1021/jm701266y.

Danusaputro, Hukum Lingkungan. Bina Cipta, 1978.

H. F. Hansen and O. Rieper, “The evedence movement: The development and consequences of methodologies in review practices,” Evaluation, 2009, doi: 10.1177/1356389008101968.

D. Handayani and A. Purwanto, “Penilaian Risiko Keselamatan Dan Kesehatan Kerja,” Din. Rekayasa, 2014.

M. Safiuddin, M. A. Salam, and M. Z. Jumaat, “Utilization of palm oil fuel ash in concrete: A review,” Journal of Civil Engineering and Management. 2011, doi: 10.3846/13923730.2011.574450.

M. W. Choirul Umam, F. Hardaningrum, and R. Durrotun Nasihien, “Analysis Of Traffic Accident Area On The Road In Gresik District Based On Geographic Information System,” Int. J. Eng. Sci. Inf. Technol., vol. 1, no. 2, 2021, doi: 10.52088/ijesty.v1i2.52.

R. Y. Widya Baskara, A. Wahyuni, and F. Hardanignrum, “The Effect Of Road Narrowing On The Traffic Characteristics,” Int. J. Eng. Sci. Inf. Technol., vol. 1, no. 2, 2021, doi: 10.52088/ijesty.v1i2.54.

SNI 03-2834-2000, “SNI 03-2834-2000: Tata cara pembuatan rencana campuran beton normal,” Sni 03-2834-2000, pp. 1–34, 2000.

Departemen Pekerjaan Umum, SK SNI S-04-1989-F : Spesifikasi Bahan Bangunan Bagian A (Bahan Bangunan Bukan Logam). Bandung: Yayasan LPMB, 1989.




DOI: https://doi.org/10.52088/ijesty.v1i2.109

Refbacks

  • There are currently no refbacks.


Copyright (c) 2021 Syafwandi Syafwandi, Danu Setyo Sembodo, Agyanata Tua Munthe, Agung Sumarno

Creative Commons License
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

International Journal of Engineering, Science and Information Technology (IJESTY) eISSN 2775-2674