Analysis of The Mechanical Properties of Concrete Based on Fly Ash and Palm Oil Clinkers

L Opirina, Azwanda Azwanda, R Febrianto

Abstract


Concrete is the result of a mixture of cement, aggregate and water. Under certain conditions, the concrete mixture can be added with additives and admixture to get the concrete as needed. Cement is the most important material in the manufacture of conventional concrete. When cement is produced, the same amount of CO2 will also be generated as a side effect and pollute the atmosphere. Fly ash as an alternative to cement will be introduced as an alternative concrete material to reduce the use of cement in the concrete mix. In addition to the use of charcoal fly ash as a partial substitute for cement, this study also uses palm oil clinkers as a substitute for fine aggregate as much as 20%. This replacement material is an industrial waste which has the main content of silica and alumina which is similar to the main material for forming concrete. In addition, the use of these two materials also aims to reduce the exploration of the use of natural materials. This research introduces 3 kinds of concrete composition. The grouping is based on the ratio of fly ash and cement used, namely (60%:40%), (70%:30%) and (80%:20%). The test object used is a concrete cylinder with a diameter of 150 mm and a height of 300 mm. Tests were carried out at the age of 28 days of concrete. The compressive strength test showed that the best concrete was produced from the combination of the addition of 60% fly ash of coal aged 28 days, which was 4.21 MPa.

Keywords


Normal Concrete, Palm Oil Clinkers, Charcoal Fly Ash.

Full Text:

PDF

References


J. Davidovits, “Global warming impact on the cement and aggregates industries,†World Resour. Rev., vol. 6, no. 2, pp. 263–278, 1994.

T. Mulyono, “Teknologi Beton: Dari Teori Ke Praktek,†no. October 2018, p. 574, 2006.

D. Maisa Putra and A. Alfauzain, “Design Of Tracer Using Microsoft Access Unit In Medical Record Primary Health In Padang,†Int. J. Eng. Sci. Inf. Technol., vol. 1, no. 3, 2021, doi: 10.52088/ijesty.v1i3.90.

E. Prianti, M. B. Malino, and B. P. Lapanporo, “Pemanfaatan Abu Kerak Boiler Hasil Pembakaran Limbah Kelapa Sawit Sebagai Pengganti Parsial Pasir pada Pembuatan Beton,†Positron, vol. 5, no. 1, pp. 26–29, 2015, doi: 10.26418/positron.v5i1.9744.

R. Y. Widya Baskara, A. Wahyuni, and F. Hardanignrum, “The Effect Of Road Narrowing On The Traffic Characteristics,†Int. J. Eng. Sci. Inf. Technol., vol. 1, no. 2, 2021, doi: 10.52088/ijesty.v1i2.54.

D. Riyan Rizaldi, A. Doyan, Z. Fatimah, M. Zaenudin, and M. Zaini, “Strategies to Improve Teacher Ability in Using The Madrasah E-Learning Application During the COVID-19 Pandemic,†Int. J. Eng. Sci. Inf. Technol., vol. 1, no. 2, 2021, doi: 10.52088/ijesty.v1i2.47.

F. Rahman and F. Fathurrahman, “Pemanfaatan Hasil Pembakaran Limbah Cangkang Kelapa Sawit sebagai Bahan Pengganti Pasir pada Pembuatan Beton Normal,†Media Ilm. Tek. Sipil, vol. 6, no. 1, pp. 30–40, 2017, doi: 10.33084/mits.v6i1.259.

R. Manuahe, M. D. J. Sumajouw, and R. S. Windah, “Kuat Tekan Beton Geopolymer Berbahan Dasar Abu Terbang (Fly Ash),†J. Sipil Statik, vol. 2, no. 6, pp. 277–282, 2014.

R. Rinaldy and M. Ikhsan, “Determinant Analysis Of Conflict On Project Results In Aceh Province,†Int. J. Eng. Sci. Inf. Technol., vol. 1, no. 1, 2021, doi: 10.52088/ijesty.v1i1.37.

A. H. Umboh and R. S. W. Marthin D. J. Sumajouw, “Pengaruh pemanfaatan abu terbang ( fly ash ) dari pltu ii sulawesi utara sebagai substitusi parsial semen terhadap kuat tekan beton,†vol. 2, no. 7, pp. 352–358, 2014.

A. Kusuma, P. Steenie, E. Wallah, and S. O. Dapas, “Kuat Tarik Belah Beton Geopolymer Berbasis Abu Terbang (Fly Ash),†J. Sipil Statik, vol. 2, no. 7, pp. 330–336, 2014.

S. Akter, M. A. Hossain, and M. M. Rahman Redoy Akanda, “A Noble Security Analysis of Various Distributed Systems,†Int. J. Eng. Sci. Inf. Technol., vol. 1, no. 2, 2021, doi: 10.52088/ijesty.v1i2.101.

SNI 03-2834-2000, “SNI 03-2834-2000: Tata cara pembuatan rencana campuran beton normal,†Sni 03-2834-2000, pp. 1–34, 2000.

V. D. Gorgots, “About drawdown drilling parameters design procedure at primary formation exposing by a horizontal wellbore,†Neft. khozyaystvo - Oil Ind., no. 9, pp. 120–121, 2006.




DOI: https://doi.org/10.52088/ijesty.v1i4.148

Article Metrics

Abstract view : 191 times
PDF - 72 times

Refbacks

  • There are currently no refbacks.


Copyright (c) 2021 L Opirina, Azwanda Azwanda, R Febrianto

International Journal of Engineering, Science and Information Technology (IJESTY) eISSN 2775-2674