Design and Fabrication of Portable Tilting Furnace for Aluminium Melting

Muhammad Yusuf, Syamsul Bahri, Agustinawati Agustinawati

Abstract


Machining is a metal cutting process using a machine tool. The machining process will produce the products and the chips or the scraps. The metal of machining chips made from machining processes can be recycled into new materials. The metal of machining chips can be recycled through the smelting process. This research aims to design and fabrication a crucible furnace that can support the recycling process of the metal scraps of machining chips into a new material—the stove is designed to melt non-ferrous metals using gas fuel. The tilting-pot crucible furnace type was created in this research. The crucible furnaces are used for nonferrous metals such as bronze, brass, zinc, and aluminum alloys. The crucible furnace capacities are limited to 10 kg. Liquefied Petroleum Gas (LPG) was used as the fuel for the furnace. The construction of the stove is cylindrically designed. The burner was installed upright at the bottom of the stove. The combustion process is done by mixing fuel LPG gas and air from the blower. The stove was tested on the aluminum machining chips using locally available materials in Lhokseumawe Aceh. The thermometer Lutron TM-906A was used to measure the temperature inside the crucible. From the results of the design and testing of the furnace that has been done, it can be concluded that the aluminum machining chips of 6kg are melting at a temperature of 640oC for 52 minutes, and the LPG gas fuel required is 1.30kg. The crucible furnace was designed to attain a maximum temperature of 700°C.


Keywords


Crucible Furnace, Aluminium Scrap.

Full Text:

PDF

References


Groover MP, Fundamentals of Modern Manufacturing: Materials, Processes, and Systems, John Wiley & Son, (2010), pp: 483-492.

Yusuf M, Ariffin MKA, Ismail N & Sulaiman S, “Surface Quality and Chip Formation in Turning of LM6 Aluminium Alloy and Particulate Reinforced Metal Matrix Composite”, Materials Science Forum, Vol. 773-774, (2014), pp. 894-901, available online: 10.4028/www.scientific.net/MSF.773-774.894

Rady MH, Mustapa MS, Shamsudin S, Lajos MA & Wagiman A, “Analyses and Optimization of Physical and Mechanical Properties of Direct Recycled Aluminium Alloy (AA6061) Wastes by ANOVA Approach” International Journal of Mechanical and Materials Engineering, Vol. 13, No. 4, (2019), pp. 270-275, available online: https://www.researchgate.net/publication/334988838

Groover MP, Fundamentals of Modern Manufacturing: Materials, Processes, and Systems, John Wiley & Son, (2010), pp: 245-248.

Tasnim FA & Zairul AZ, “Enhanced Heating Mechanism of the Electric Metal Melting Furnace in Traditional Foundry.” Journal of Engineering and Applied Sciences, Vol. 10. No. 21 (2015), pp. 9659-9663, available online: http://www.arpnjournals.org/jeas/research_papers/rp_2015/jeas_1115_2964.pdf

Olalere AA, Dahunsi OA, Akintunde MA & Tanimola MO, “Development of A Crucible Furnace Fired With Spent Engine Oil Using Locally Sourced Materials,” International Journal of Innovation and Applied Studies, Vol. 13, No. 2 (2015), pp. 281-288, available online: http://www.ijias.issr-journals.org/abstract.php?article=IJIAS-15-112-05

Bhandari SS, Badadal SB, Kinagi VG, Tuljapurkar HS & Bansode SH, “Design and Fabrication of Crucible Furnaces by using Black Smithy Setup,” International Journal of Engineering and Management Research, Vol. 8, No. 4 (2018), pp. 131-134, available online: doi.org/10.31033/ijemr.8.4.16




DOI: https://doi.org/10.52088/ijesty.v2i2.250

Refbacks

  • There are currently no refbacks.


Copyright (c) 2022 Muhammad Yusuf

Creative Commons License
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

International Journal of Engineering, Science and Information Technology (IJESTY) eISSN 2775-2674